Flame extension and the near field under the ceiling for travelling fires inside large compartments

Structures need to be designed to maintain their stability in the event of a fire. The travelling fire methodology (TFM) defines the thermal boundary condition for structural design of large compartments of fires that do not flashover, considering near field and far field regions. TFM assumes a near field temperature of 1200°C, where the flame is impinging on the ceiling without any extension and gives the temperature of the hot gases in the far field from Alpert correlations. This paper revisits the near field assumptions of the TFM and, for the first time, includes horizontal flame extension under the ceiling, which affects the heating exposure of the structural members thus their load-bearing capacity. It also formulates the thermal boundary condition in terms of heat flux rather than in terms of temperature as it is used in TFM, which allows for a more formal treatment of heat transfer. The Hasemi, Wakamatsu, and Lattimer models of heat flux from flame are investigated for the near field. The methodology is applied to an open-plan generic office compartment with a floor area of 960 m² and 3.60 m high with concrete and with protected and unprotected steel structural members. The near field length with flame extension (fTFM) is found to be between 1.5 and 6.5 times longer than without flame extension. The duration of the exposure to peak heat flux depends on the flame length, which is 53 min for fTFM compared with 17 min for TFM, in the case of a slow 5% floor area fire. The peak heat flux is from 112 to 236 kW/m² for the majority of fire sizes using the Wakamatsu model and from 80 to 120 kW/m² for the Hasemi and Lattimer models, compared with 215 to 228 kW/m² for TFM. The results show that for all cases, TFM results in higher structural temperatures compared with different fTFM models (600°C for concrete rebar and 800°C for protected steel beam), except for the Wakamatsu model that for small fires, leads to approximately 20% higher temperatures than TFM. These findings mitigate the uncertainty around the TFM near field model and confirm that it is conservative for calculation of the thermal load on structures. This study contributes to the creation of design tools for better structural fire engineering.     

高性能三水醋酸钠-尿素-膨胀石墨混合相变材料的制备及其在电地暖中的应用性能

采用尿素调节三水醋酸钠的相变温度到合适范围再添加膨胀石墨来降低过冷度，研制了高性能的三水醋酸钠-尿素-膨胀石墨混合相变材料，并对其在电地暖中的应用性能进行了研究。结果表明，当尿素质量分数为36.5%、膨胀石墨添加量为4%(质量)时，所得混合相变材料的熔化焓高达209.1 J/g，熔点在31.98℃，过冷度仅为2.04℃，热导率为2.349 W/(m·K)，热可靠性良好；将用该混合相变材料制成的相变板安装在实验房的电地暖中时，实验房的热舒适度随着相变材料层厚度的增加而增加，但也带来加热时间和用电量的增加；当相变材料层厚度为10 mm时，电加热温度适宜设置在45℃；在热舒适度相当的条件下，有相变板的实验房与无相变板的参比房相比具有用电量小及电费低的优势。     

热仿真技术在加固显示器热设计中的应用

根据某型加固显示器的应用环境及内部功能模块的热特性,选择强迫风冷的散热方式,并通过热仿真计算指导风扇选型,根据仿真结果验证散热方案的可行性。最终,依据试验结果验证仿真结果的准确性,为加固显示器的热设计提供思路。     

Fabrication of poly(ε‐caprolactone) (PCL)/poly(propylene carbonate) (PPC)/ethylene‐α‐octene block copolymer (OBC) triple shape memory blends with cycling performance by constructing a co‐continuous phase morphology

In this paper, a triple shape memory material was prepared by ultra‐simple melt blending from poly(ε‐caprolactone) (PCL), poly(propylene carbonate) (PPC) and ethylene‐α‐octene block copolymer (OBC). The obtained material possessed a co‐continuous phase morphology and presented an excellent triple shape memory effect (triple‐SME). Theoretical prediction demonstrated that a special continuous phase morphology could be constructed by adjusting the proportions of the blend. Moreover, the results indicated that a close relationship existed between the phase morphology and the triple‐SME of PCL/PPC/OBC. The sample with 35 vol% PPC content contributed to the formation of a continuous phase morphology and exhibited the optimal triple‐SME. Additionally, the sample PCL/PPC/OBC (32.5/35/32.5) showed outstanding structure and performance stability during cycle loading–unloading tests, which evidenced the prominent cycling shape memory property (nearly 100% shape fixing and recovery of temporary shape). Overall, this work could provide an efficient, convenient and recyclable method to obtain high‐performance shape memory materials. © 2020 Society of Chemical Industry     

PAN纤维共聚单体作用机理的光电离质谱研究

本工作以丙烯腈/衣康酸（IA）二元共聚原丝以及丙烯腈/IA/丙烯酸甲酯（MA）三元共聚原丝为研究对象，利用热重分析仪（TG）和热解-同步辐射真空紫外光电离质谱（Py-SVUV-PIMS）对其热稳定化过程进行研究。TG结果表明，氮气气氛下，二元共聚原丝（PAN/IA）和三元共聚原丝（PAN/IA/MA）分别呈现三阶段和两阶段的热分解过程，其中PAN/IA的第一和第二阶段均对应PAN线型分子链的断裂，但前者是由自由基环化反应放热引发的，后者则是由正常温度下的热分解所致，而单体MA的加入显著抑制了自由基环化反应，使得PAN原丝的热稳定化能够以单体IA诱导的离子型环化反应为主较平缓地进行，相应的热失重过程也由两阶段转变为了单阶段。Py-SVUV-MS的实验结果表明，两种共聚PAN原丝在程序升温过程中会生成包括含氮小分子、丙烯腈单体及低聚物、成环化合物在内的三类主要热解产物，对比各类产物的生成趋势和产量，推断单体MA通过降低PAN结构的规整度，使其无定形化，从而增加环化反应的引发点，促进PAN原丝向稳定的预氧丝转变，同时由典型热解产物——甲基丙烯腈的生成路径可知，MA本身并不参与PAN大分子的环化反应，属于中性共聚单体。空气气氛下，CO₂的产量差异也间接证明了MA单体能够有效提升PAN纤维的固碳能力，采用三元共聚方法制得的PAN纤维热稳定性能更佳。     

Effect of marinating ingredients on temperature-induced denaturation of hemoglobin and its relation to red blood spot formation in cooked chicken breast

Red blood spot (RBS) commonly found in cooked chicken breast has caused severe economic loss as it is perceived as a sign of undercooked product. The objectives of this study were to investigate the cause of RBS as related to common ingredients used in marination, based on both chicken breast and isolated chicken hemoglobin (Hb) models. The effect of sodium chloride (NaCl), sodium tripolyphosphate (STPP), and glucose on thermal denaturation of Hb was investigated along with the extent of RBS formation in cooked marinated chicken breast. After vacuum tumbling for 65 min and subsequent storage at 4 °C for 20 hr, STPP and glucose were not absorbed into the center of chicken breast. However, Na⁺ was absorbed after 12 hr storage. The denaturation temperature (T_d) of isolated chicken Hb decreased to 65.8 °C in the presence of 1.5 M NaCl, while that of the control was 69.4 °C. STPP at pH 9 decreased T_d of Hb to 61.4 °C. The alkaline pH induced by STPP destabilized the Hb structure. RBSs were observed at 100% incidence when cooked to core temperatures of 50 and 70 °C for 1 min. RBSs were completely eliminated at core temperature of 85 °C. The ingredients used during marination appeared to have a minimal effect on RBS formation due to their limited absorption into the chicken breast. The cooking temperature is a major factor governing RBSs, as it directly affects the denaturation of Hb.     

Developing microencapsulated 12‐hydroxystearic acid (HSA) for phase change material use

Phase change materials (PCM) have an increasingly more important role as a thermal energy storage (TES) media. However, leakage problem of PCM causes limitation during their integration in TES systems. Therefore, the encapsulation of PCMs is attracting research interest to extend usage of PCMs in real TES applications in recent years. In this study, hydroxystearic acid (HSA) was encapsulated with polymethyl methacrylate (PMMA) and different PMMA comonomer shells via emulsion polymerization method for the first time in literature. HSA with high melting temperature range (74–78°C) can widen the scope of using PCMs, and the encapsulated form can make it more versatile. The chemical structures, morphologies, and thermophysical properties of capsules were determined by FT‐IR, SEM, DSC, TGA, and thermal infrared camera. Among the produced HSA capsule candidates, PMMA‐HEMA is the most promising with latent heat of 48.5 J/g with melting range of 47 to 85°C. SEM analysis indicated that the capsules have spherical shape with compact surface at nano‐micro (100–440 nm) size range; however, some capsules exhibited agglomeration.     

Local body cooling to improve sleep quality and thermal comfort in a hot environment

The effects of local body cooling on thermal comfort and sleep quality in a hot environment were investigated in an experiment with 16 male subjects. Sleep quality was evaluated subjectively, using questionnaires completed in the morning, and objectively, by analysis of electroencephalogram (EEG) signals that were continuously monitored during the sleeping period. Compared with no cooling, the largest improvement in thermal comfort and sleep quality was observed when the back and head (neck) were both cooled at a room temperature of 32°C. Back cooling alone also improved thermal comfort and sleep quality, although the effects were less than when cooling both back and head (neck). Mean sleep efficiency was improved from 84.6% in the no cooling condition to 95.3% and 92.8%, respectively, in these conditions, indicating good sleep quality. Head (neck) cooling alone slightly improved thermal comfort and subjective sleep quality and increased Stage N3 sleep, but did not otherwise improve sleep quality. The results show that local cooling applied to large body sections (back and head) could effectively maintain good sleep and improve thermal comfort in a hot environment.     

CFD modeling of thermal contact resistance between solid contacting surfaces

Heat transfer has considerable applications in different industries such as designing of heat exchanger, nuclear reactor cooling, control system for spacecraft, and designing of microelectronics cooling. As the surfaces of two metals contact each other, this issue becomes so crucial. Thermal contact resistance (TCR) is one of the key physical parameters in heat transfer of mentioned surfaces. Measuring the experimental value of TCR in laboratory is highly expensive and difficult. As an alternative, numerical modeling methods could be engaged. In this study, inverse problem method solution is utilized as a proper method for estimation of TCR value. In this order, three different configurations (flat-flat, flat-cylinder, and cylinder-cylinder) were utilized in two steady and unsteady state conditions to predict the value of TCR. A comparison between the measured values and obtained values from the simulation show the errors for flat-flat, flat-cylinder, and cylinder-cylinder configuration after 10 min from starting the experiment are 4.6074%, 0.1662%, and 0.5622%, respectively. And in steady-state condition, the corresponding errors are 6.06e-3%, 1.506%, and 0.846%, respectively. In conclusion, the final results establish the fact that the inverse problem method solution can predict TCR values between contacting surfaces.     

地埋管换热器分区运行对土壤热堆积特性影响的研究

为了缓解埋管区域土壤的热量堆积问题,提出了埋管换热器按内中外、块状、间隔三种分区运行的策略,利用CFD软件建立了10×10的井群换热模型,对地源热泵系统在三种分区与不分区运行策略下运行十年进行数值模拟,分析不同分区运行策略对土壤温度分布和土壤热堆积特性的影响。模拟结果可知:不分区、内中外分区、块状分区、间隔分区四种运行策略下埋管区域的平均温度分别为25.23、23.31、23.06、23.28℃,最高温度分别为40.62、32.77、40.65、38.93℃;分区运行较不分区运行可以有效缓解热堆积作用,埋管区域整体温度较不分区运行时降低了2.00℃左右,内中外分区策略可以显著缓解埋管区域热堆积。